M-100 Message Board
M-100 Message Board
Home | Profile | Register | Active Topics | Members | Search | FAQ
Username:
Password:
Save Password
Forgot your Password?

 All Forums
 M-100 Message Forum
 Fuel Management
 Need Help Replacing Fuel Pump
 New Topic  Reply to Topic
 Printer Friendly
Author Previous Topic Topic Next Topic  

cmcnamara

USA
1 Posts

Posted - 11/19/2017 :  14:29:42  Show Profile  Reply with Quote
Hi, I'm trying to replace the MFIP on my 600. Can someone explain to me what I do after setting engine to 60 after TDC?
Manual says to remove the distributor cap and to turn the crankshaft to the point at which the distributor rotor points to No 1 cylinder marking on the distributor housing.
If I start at 60 degree and then turn the crankshaft some more won't I be "way" past 60 degree after top dead center?
Thanks, Chris

Primo

12 Posts

Posted - 11/24/2017 :  05:31:26  Show Profile  Reply with Quote
Einbauen
Anm.: Vor dem Einbau einer Ersatz-Einspritzpumpe ist die Regelstange auf Leichtgängigkeit zu prüfen (siehe Abschnitt A).
8 Kolben des 1 . Zylinders auf 60° nach ZündOT stellen.
Zündverteilerkappe abnehmen und Motor an
der Kurbelwelle so weit durchdrehen, bis der
Verteilerläufer auf die Markierung am Verteilergehäuse für Zylinder 1 zeigt und am Schwingungsdämpfer die OT-Markierung anzeigt.
Motor bis zur 60°-Markierung weiterdrehen.
Nockenwelle der Einspritzpumpe drehen, bis
sich die Markierungsstriche auf der Nockenwelle und dem Flansch gegenüberstehen (Bild
07-12/7)


After you have installed the TDC and the distributor pointed to the first cylinder, rotate the pulley to the 60 degree mark.
Everything, you can install the pump with the mark.
Go to Top of Page

paul-NL

Netherlands
4248 Posts

Posted - 11/24/2017 :  06:41:48  Show Profile  Reply with Quote

see this thread :
http://www.m-100.co/forum/topic.asp?TOPIC_ID=7665

because these motors are FOURstroke engines you have to search first the right TDC by doing the distrybution rotor pointing to cilinder 1 .
After that you turn the motor further to the 60 degree marking.

Set the markings from the FIP as in the picture of the above mentioned link.

Then put all together

Succes ....

Edited by - paul-NL on 11/24/2017 06:42:53
Go to Top of Page

Primo

12 Posts

Posted - 11/24/2017 :  09:07:14  Show Profile  Reply with Quote
And it will work like our W100 after assembling today;)
https://yadi.sk/i/oJXNsYrH3Pzkj6

Good luck!
Go to Top of Page

paul-NL

Netherlands
4248 Posts

Posted - 11/24/2017 :  11:17:23  Show Profile  Reply with Quote

Primo,

can you tell me the Vin of your 600 for our registery and could I recieve some info and pictures ??

If you don't want to have it public send me a PM by clicking on my poster name.
Go to Top of Page

Primo

12 Posts

Posted - 11/24/2017 :  18:13:42  Show Profile  Reply with Quote
Hello, paul-NL!

Send please the address of your email in PM, I will send a photo in the letter and VIN number.
Go to Top of Page
  Previous Topic Topic Next Topic  
 New Topic  Reply to Topic
 Printer Friendly
Jump To:
M-100 Message Board © 2002-2015 International M-100 Group, Inc. Go To Top Of Page
This page was generated in 0.2 seconds. Powered By: Snitz Forums 2000 Version 3.4.06